Marlin 1.1 Z-Homing to Probe lowers bed before raising. (1 reply)
Hi Everyone, My CoreXY machine has been dormant for almost a year until this week when I brought her back to service. In the process I upgraded the Marlin Firmware to 1.1 and it appears there is a new...
View ArticleUltimaker with hiwin linear rails (5 replies)
This has got me curious. Lets assume an ultimaker like gantry movement (quadrap) is replaced with linear rail and powered by single motor with each axis driven by an 5 or 8mm rod connected with a...
View Article24V 8-bit controller board recommendations (4 replies)
Hi all, I'm finalising specs for building a Hypercube design. Since I want to use 24V but still keep using Marlin. Any recommendations for ready to use 8-bit board capable of 24V? Bonus if easily...
View ArticleDirection of z-axis (no replies)
Hello everyone. I have a small, and a bit stupid question. :S I am setting up the controller on my new printer, and I realize I do not know what's up and down on a corexy printer. My design is a...
View ArticleIDEX and IDE...Y? (6 replies)
Hi, I need your opinion about something, does it seems possible, with a CoreXY architecture, to have two separate X axis on two separate Y axis. With this, there will be four printing heads, one at...
View ArticleNewbie looking for some setup guidance... (4 replies)
First post to the forum so excuse the newbieness here.. So, I've just finished building and wiring my CoreXY and I'm using a DuetWifi board but I'm having a few setup issues in regards to setting up...
View ArticleIt's Begun (no replies)
So in the Engineering Block Program at my high school my friend and I are building a larger CoreXY printer. Here's the first picture. Like a Tank [imgur.com] All I can say is that Aluminum Extrusion...
View ArticleMy printer is now printing.. :) (no replies)
Hi every one I have now crossed a big milestone in my 3d printer project. I have started making the first prints on it. I began just over 10 months ago with no experience in 3D printers, and a Prusa...
View ArticleThe location of the Z endstop (2 replies)
Hi every one. I have a small question about z-endstops. I know where to put my endstops for X and Y, but I do not know where to place Z. For me, it would be logical to place it at max (that's when my...
View ArticleE3D Titan on a D-Bot carrier (1 reply)
I wasn't very pleased with the print quality of the D-Bot with Bowden tube extruder. Especially PETG had lots of blobs and strings. So I want to try out the Titan. I mounted it with a readily...
View ArticleZ motor noise from binding... how do you align? (1 reply)
I'm noticing as my Z axis gets closer to my motors that there appears to be some binding. Anyone have a solution for aligning the motors/lead screws with the bed and carriages? ampapa,
View Articleproblemas con el extrusor (no replies)
Tengo un problema al colocar a calentar el extrusor el lo hace pero cuando esta en 200 c y le eligo en el repetier-host para mover el filamento no lo hace. tienen idea de a que se deba? uso un...
View ArticleClik here to view.
Announcing Rosalind, a parametric CoreXY 3D printer designed in OpenSCAD and...
Hi all, I'm new here and I hope I'm posting in the right forum. I just completed a first working prototype of rosalind, a CoreXY printer. The code is still a mess, but in the spirit of "release early,...
View ArticleCyclonit's CoreXY (1 reply)
Hi! A few weeks ago I've started designing a new Core XY printer based on the Hypercube Evolution from Scott3D. My main goal was a 300x300x300mm build volume in a 500x500x500mm profile (+ bowden tube...
View ArticleWitor's coreXY (no replies)
Firstly I would like to say hello as it is my first post on this forum. I have spent past few weeks thinking about making a new 3d printer. I currently own an Anet A6 which is a decent printer (after...
View Article20x20 aluminium tubing frame (2 replies)
Hello! I’ve been lurking for a year or so and thought I should finally contribute something. Short story, TLDR at bottom. I built a Prusa/Mendel style scraprap to be able to print parts for a coreXY....
View ArticleClik here to view.
Help with strange blobs/calibration (1 reply)
So I got my corexy assembled a couple months ago but was traveling and only now I can take care of some issues. I am unsure if that's a lack of alignment, or wrong belt tension or something else, but...
View ArticleHow can i configure Hbot on marlin firmware? (no replies)
How can i configure Hbot on marlin firmware 1.1.8
View ArticleOne corner issue (2 replies)
I have finished building my CoreXY with 370mm cube size. [openbuilds.com] For control MKS board with smoothieware is used. There is an issue with one corner as per image. Any ideas? This is with...
View ArticleTall print issue in X direction (1 reply)
Another issue occured. When tried to print tall object, 35cm rocket. It was printed in PLA with 2 perimeters and in upper part it looks terrible. Lower is ok for me. It is much worse in X direction...
View Article