Yet more odd CoreXY woes (no replies)
I decided to create a CoreXY using a Duet Maestro and a bunch of spare parts that I had lying around. I have gotten Delta's down to a science, and while they are easy to build, and space stingy, they...
View ArticleTronxy X5SA-500-PRO leveling issue (no replies)
[youtu.be] I recently purchased a Tronxy X5SA-500-Pro printer and have been having troubles. Even after resetting to factory settings and leveling out the z-axis motors, the auto-leveling still says...
View ArticleTronXY X5 first layer under extrusion (1 reply)
Recently I've upgrade my tronXY X5 to ramps board. Since I didn't find any marlin code to my printer I've get one from a tronXY X5S project and now I'm converting to my printer. At this point I'm...
View ArticleFirst build question. (1 reply)
Hi, I am doing my first build of a core x/y hypercube with a Bigtreetech SKR 1.3 board. I am just bringing my z motors alive and I am testing one at a time to make sure I have them connected...
View Articlemarlin 2.0 bltouch does not work (no replies)
Hi, I have a CoreXY hypercube machine.I bought the new MKs robin nano v2 card and installed 3dtouch.I did the Settings from Marli.Unfortunately, when I do z home, it doesn't stop the table.The needle...
View ArticleTronxy X5SA Pro - Marlin settings, removing auto level sensor and adding...
Currently I am having some issues with the proximity sensor that came with the printer (see here), so I have hooked up the extra limit switch that it came with and wired it to the board. Does anyone...
View ArticleBTT TFT35 v3.0 (no replies)
I have what started off as a Flsun CUBE, and was using both a 12864 and a MKS TFT35 screen. They both worked, but I would prefer only the one device that does both, just sounded easier to me. I am...
View ArticleCoreXY build question (1 reply)
Hi all, new member today! I have been in printing for 6 months with an Ender 3 and have been really happy with it. I always wanted to make my own so with the myriad of parts available out there I just...
View ArticleAnew, smaller sand table mechanism: Arrakis (no replies)
I've been building a smaller sand table that will be coffee table sized (600 x 990 drawing area). Like the original, it uses a stacked belt corexy mechanism driven by iHSV-42 servomotors at up to 1600...
View ArticleCore XY Won't stop homing at endstop (1 reply)
I have an Airwolf Axiom printer that I'm trying to write new firmware for. I'm using Marlin 2.07 on VS Code. It is a Core XY machine where it homes at front, left with the build plate at the bottom of...
View ArticleScreen and configuration issues with new Sapphire Plus printer (no replies)
Hi, I've issues with a new Sapphire Plus printer that I didn't manage to operate. The printer's controller is MKS Robin 1.2. 1. The Touch screen is not working properly, When I press a screen button,...
View ArticleNeed a CoreXY Direction (3 replies)
Hi, I've been very happy with the results of my little FoldaRap, but therein lies the problem. It's a bit small. Z-Axis homing takes too long, I'd like to enclose it and maybe heat the enclosure, etc,...
View ArticleExtruder for heated chamber? (1 reply)
I'm working on a printer to print ABS. I am planning for a heated chamber and from what I've read I need ~50-60°C. Quality is more important than speed so I don't mind toting an exrtruder around on...
View ArticleClik here to view.
X axis wobble in corexy printer (2 replies)
I recently noticed the X axis wobbling in my newest sand table mechanism when the magnet carriage moved back and forth along the X axis with Y fixed. That got me thinking that maybe something similar...
View ArticleCoreXY Z axis design questions. (3 replies)
Hey there, I'm designing a cost friendly-ish CoreXY printer using parts I have laying around and mostly off the shelf components, while still maintaining the benefits of more mainstream CoreXY...
View ArticleE3D Hemera Direct Kit or Bowden V6 for Sapphire Plus? (no replies)
Hi, Should I upgrade Sapphire Plus to E3D Hemera Direct Kit, Bowden V6 or maybe something else? I'm concerned that a moving mass of about 400 grams may cause ringing. BTW, aren't 6mm belts, to narrow,...
View ArticleQuestion regarding CoreXY design (in particular the_digital_dentist's UMMD)...
Recently, I have been studying CoreXY builds. My longer term goal is to build one, and while it is clear to me that this will include some trial and error, I hope to learn as much as possible from...
View ArticleBed probe bias along X axis. (no replies)
I am working on a new Ender 6 CoreXY printer, to which I've made the common BLTouch modification. This uses factory-provided wiring and a mount point inside the fan shroud. Unfortunately, I have a...
View Articlex-axis supports: (2 replies)
I'm trying to figure out how to make my x-axis lighter, especially since I'm considering DDDE (Direct Drive Dual Extrusion). However, with the extra weight of the print head, I'm wondering what I can...
View ArticleImpressions of the DiyCore System (no replies)
I've been sourcing parts for my upcoming printer build for... quite some time now. While looking for linear rails, I found this, which is the 3dfused DIYcore system. It looks like a fantastic machine...
View Article