Error when Connecting from laptop... (1 reply)
Hey Guys. Funny problem just occured... when I try to connect to my SKRv1.3 it says connection ans starts a list of M105's ??? If connects on my stationary PC but not the laptop... Its true for both...
View ArticleHypercube vs HEVO 200x300 single Z motor (no replies)
I've already build a version of a hypercube original from tech2c with a 220x220 bed and it's perform great. Now i'm looking for a designer to build a coreXY with 200x300 or a 270x240 (ultrabase bed)....
View ArticleInverted Z Steppers Railcore (no replies)
I am building a Railcore 450 X450 X550 using t10 leadscrews and was wondering why i couldn't mount the z steppers up top with everything else and not have to worry about weight twist and whatnot
View ArticleI need a fonctional Marlin (3 replies)
I built a coreXY printer controlled by Marlin-1.1.8 and pronterface or repetierHost. I've been struggling for days to find the solution to problems that keep me going in circles. I would like to have...
View Article5mm idler spacers? (2 replies)
G'Day Gang, I am putting together a corexy machine and I want to use GT2 plane idlers but have not been able to find a successful spacer solution to nest 2 idlers on the same shaft. I cannot find...
View ArticleCore XY build - feedback appreciated (8 replies)
For the last couple of months i've been designing a Core XY 'dream machine' based roughly on the E3D tool changer. I'm now at the point of ordering alu plates to be waterjet cut. The idea is to create...
View ArticleI'm designing a CoreXY Machine. (no replies)
Here are some pics of where I'm at currently. I have the whole machine modeled on my PC. Im printing, tweaking, and assembling now. I have a bunch of parts already printed, but some of them I want to...
View ArticleKEEVO (my second design) (no replies)
Hello everyone, I would like to show you my second design and possibly get some constructive feedback of course! :-) I have posted it on thingiverse -> [www.thingiverse.com] . This was my first...
View ArticleCaffeineXY (2 replies)
First time poster, long time lurker (ish). Been printing for about 2 years, and like to design and make stuff, so after deciding that I've had enough of my chinesium printers it's time to make...
View ArticleExtruder changes direction automatically (no replies)
Hi, I hope someone can help me with the following problem. I am using a Bigtreetech SKR PRO v1.1 board with TMC2208 drivers and Marlin 2.0.x. I used other firmware the bug fix, however they all have...
View ArticleFirst build question. (1 reply)
Hi, I am doing my first build of a core x/y hypercube with a Bigtreetech SKR 1.3 board. I am just bringing my z motors alive and I am testing one at a time to make sure I have them connected...
View ArticleCOREXY Motion Asymmetry (1 reply)
I have built several FDM printers using the COREXY motion system with good success. I recently decided to try and improve print quality where motion induced artifacts were visible. I used a typical...
View ArticleNozzle to low after auto bed level grrrrrr (no replies)
Hello all , Ik have some troubles with my nozzle hight . I adjusted the z off set with M851 and stored it with M500 and active with M501when i check with M503 it's correct . When i look in the eeprom...
View ArticleZ Axis Design Help (5 replies)
I've designed my own Core XY and finally got to the part where I put together the Z axis bed supports, etc. The cube is 500mm^3 with a print bed area of up to 300x300mm I'm using two 8mm threaded rods...
View ArticleWhich Model as Basis for Rebuild (6 replies)
Hello All, I am looking to build a fast corexy machine and thought I would start with an existing unit for the first try/testbed. Here are three potential options - what do you think? TIA
View ArticleWhich Kit? Railcore? SecKit? Other? (4 replies)
Because I am not now in a position to build from scratch, I posed a question about a commercial corexy that could be improved. I was thinking along the lines of the Ender 3, where for not a lot of...
View ArticleClik here to view.
Linear Rail - CoreXY 326x326x320 (no replies)
I set up a little project page. I'll update it from time to time when I got time and new stuff happened. V1.2.jpg FFFPrinterFinalBuild-1024x960.jpg I always wanted a 3D printer of my own. Since no...
View ArticleQuestions about TronXY X5SA (21 replies)
I got a CoreXY kit to learn about corexy and to boost my PPE production for our local Maker group. A lot of this machine is good, solid bones, bolted together, no plastic corner pieces and 99% steel,...
View ArticlePrinter design: ParalaXXY (5 replies)
Hi everyone! About 3 years ago I started into 3D printing with a P3Steel Toolson MK2. I still use it as of today, and recently, I printed a few of stuff for the COVID-19 medical teams. While my...
View Article